Freud 73-214: 1/2" (Dia.) O-Flute Up Spiral Bit with 1/2" Shank 1/2-Inch Diameter by 1-1/8-Inch Height O Flute Up Spiral Plastic Cutting Router Bit with 1/2-Inch Shank

Brand:Freud

3.7/5

€
112.47

Freud Premier Solid Carbide. Use in CNC, hand-held and table-mounted routers. O-Flute design cuts cooler, avoids melting. Up Shear design clears chips fast, delivers cleanest cut on bottom surface. Smooth cuts in solid surface and plastics. Specs: Number of Cutters 2, Overall Dia. 1/2", Overall Length 3-1/2", Shank Dia. 1/2", Carbide Height 1-1/8".

Amount

Add to Cart Buy now

EAN: 0008925059981

Categories Power & Hand Tools, Power Tool Parts & Accessories, Router Parts & Accessories, Router Bits, Straight, Spiral & Trim Bits, Spiral,

Brand	Freud
Item Weight	0.28 Pounds
Material	Polycarbonate
Size	One Size

5 Star

4 Star

3 Star

2 Star

1 Star

Write your review

Your email will not be published. All mandatory fields are marked with^*

Your rating

Scritto da: Arthur E. Sigler Jr

Great for plastics, acrylic especially

I had to cut out two 17” circles of 1/8” acrylic. The circles could not have any holes. I had to sandwich the acrylic between to pieces of 1/4” MDF to keep the acrylic from vibrating. I also used double sided tape since clamping the sandwhich wasn’t working well. The Router bit did a great job. No fracturing or cracking and the edge only needed a quick cleanup with 400 grit then I passed a flame all the way around the edge of each and ended up with a glass smooth clear edge. Only after a couple failures using some scrap though did I accomplish the task.

Scritto da: mossyboy6

Genuinely a quality bit

I do production plastic work on a cnc router. Delrin, and HDPE mostly, with some Acrylic and PVC thrown in. I have used Vortex, Amana, Onsrud, and many more, this bit is just as high of quality as the $70+ bits that I have of this size for plastics. If I could only have one bit for plastics, this might be it.

Scritto da: Darsh

Great plastic cutting bit.

Had absolutely no issues running this bit in plexiglass. Smooth cuts, great chip extraction, and clean finishing on the surface. Ran it just a hair above the lowest speed my DeWalt 611 router runs.

Scritto da: Mike

Good bit for ABS plastic

Need to go slow in ABS. If your piece is not secured real good, you get a lot of chatter. This bit will cut ABS very well. No burning or melting. It cuts a lot of fine chips away from the work and seems to stay cool.

Scritto da: Reginald Yoshizaki

Router bit

Great clean cuts

Scritto da: Anonymous

Worked great for cutting acrylic

Worked great for cutting acrylic

Scritto da: Topfuelgeorge

get the right bit

this bit works great on acrylics and hard plastics

Scritto da: Amazon Customer

worked great

Cut some plastic sheet like butter.

Scritto da: honestreviews.

Dissapointing in Freud.

I had boughten a cheaper brand o-flute router bit with a single flute and it seemed to work not too bad so I figured I'd get a Frued o-flute router bit with two flutes and thought it was going to work great. But was sorely disappointed. The single-flute router bit didn't want to grab my workpiece which was the best part about it since it seems that every router bit seems to do that with HDPE. Which makes it dangerous to work. The Frued wasn't as bad as just a normal flush trim bit but didn't come close to the cheaper version. I returned it.