Stens 265-069 Belt Compatible with/Replacement for AYP: 532140294, 140294; Husqvarna: 532140294, 531300768; McCulloch: 532 14 02-94; Jonsered: 532 14 02-94; Craftsman: 24103

Brand:Stens

3.6/5

€
61.20

Stens branded parts are trusted by professional dealers to perform OEM quality repairs. The Stens name is featured on all Genuine Stens product packaging. Stens one-year warranty ensures reliability and performance for every part. Fits: WE185H42F and Y18H44D Hydrwith 42" and 44" deck, LTH1342, LTH1342A, YTH150, YTH1542XP, YTH1542XPG, YTH1848XP, YTH1848XPF, YTH2242A, YTH2242B and YTHP1542. Compatible with/Replacement for OEM Number: AYP: 532140294, 140294; Husqvarna: 532140294, 531300768; McCulloch: 532 14 02-94; Jonsered: 532 14 02-94; Craftsman: 24103. Specs: Belt Application: Drive. Belt Type: Covered. Width: 1/2". Length: 82".

Amount

Add to Cart Buy now

EAN: 0023899163434

Categories Patio, Lawn & Garden, Outdoor Power Tools, Replacement Parts & Accessories, Lawn Mower Parts & Accessories, Lawn Mower Replacement Parts,

Country of Origin	USA
Customer Reviews	4.5 4.5 out of 5 stars 49 ratings 4.5 out of 5 stars
Is Discontinued By Manufacturer	No
Item model number	265-069
Item Weight	6.4 ounces
Manufacturer	Stens
Product Dimensions	13 x 6 x 3 inches

5 Star

4 Star

3 Star

2 Star

1 Star

Write your review

Your email will not be published. All mandatory fields are marked with^*

Your rating

Scritto da: Dan

Perfect replacement for a Craftsman LT1000 riding mower With Hydrostatic Drive

I installed this part on my Craftsman LT1000 riding mower (model number 917.270680). It was an exact replacement for the OEM drive belt (NOT deck belt) with part number 532140294. My mower has a hydrostatic drive and it works great but I'm not sure if it would fit similar models with a geared transmission.

Scritto da: Amazon Customer

Fits and works great once you figure out how to install it!

Belt fit perfectly once I figured out how to put it on my Husqvarna YTH18542 riding lawn mower. Instructions that came with lawn mower are very poorly written. States that you should work the belt down and off around the electric clutch. Reading an older comment below helped. I have an electric clutch and there was no way the belt would come off around the clutch. Didn't even try because it was clearly impossible. THE FIX: Pulling the belt off the pulley upwards around the engine shaft gave me another couple inches to work with. I was able to carefully put one side of belt in between a fan blade and VERY CAREFULLY spin the fan blade pulley and belt and it came off. Whewwww! Re-install the same way putting the belt above the pulley around the engine shaft. Then work it around the fan blades carefully. Then around the idler and tensioner spindles. Also, I had a very difficult time disconnecting the electric clutch pulley wire connector. Must have been some rust inside the connector. It did come off and afterwards I put a liberal amount of dielectirc silicon inside the connection before re-connecting just in case I need to remove again. Hope this helps other DIY-ers!

Scritto da: Salvador B Castanon

Great

Perfect fit, works great.

Scritto da: R. A.

Good replacement

Very tight quarters and hard to install. Don't follow manual and remove from the clutch side first. Much easier to work belt ABOVE the clutch pulley first and them work up and off the transaxle pulley. Carefully work over the plastic fan blades and then replace in the reverse order.

Scritto da: Arkansas Runner

Only lasted 7 months

I'm very disappointed by Stens belts. I purchased this belt in March 2018 as a replacement for the OEM Husqvarna ground drive belt on my 48" riding mower. Though this was a relatively mild grass growing season, resulting in fewer hours of use, this belt only lasted 7 months before it stretched to the point that it could no longer drive the mower up the mild slopes in my yard. Unfortunately, in April I purchased two other Stens belts for the same tractor's mower deck belts. I replaced one in August (it more or less fell apart) and when I inspected the mower belts yesterday discovered the other is in the process of failing and now must be replaced. So, a total of 3 belts, none of which lasted more than 7 months on a 48" lawn tractor that's used exclusively to mow my approximately 2/3 acre yard. Pitiful!

Scritto da: Barbara J. Macedo

Price and availability,reliableity

???????????????????????????? was ok,did the job

Scritto da: David

Four Stars

Can't say about durability but it fit my Husky mower perfectly and appears well made

Scritto da: D.H.

Exactly as described

Mower deck belt. Correct dimensions for application

Scritto da: rf brown

Four Stars

Good quality. Quick delivery from US yet still much cheaper than genuine Husqvarna belt