BOSCH 85146 1/4-Inch High Speed Steel Pilot Panel Bit with Drill-through Point-Single Flute

Brand:BOSCH

3.4/5

€
45.73

PRODUCT DESCRIPTION The BOSCH line of countersinks are great for deburring and chamfering openings to pre-drilled holes. Great for electrical, plumbing and HVAC contractors. BOSCH countersinks cut varied materials cleanly and accurately. With standard high-speed steel and super hard titanium-coated bits, these countersinks perform great in even the toughest materials. FROM THE MANUFACTURER Bosch router bits are distinguished for their careful selection of materials, exactly calculated cutting geometry, long bit life, extra sharp cutting edges and low vibration.

Amount

Add to Cart Buy now

EAN: 0000346048797

Categories Power & Hand Tools, Power Tool Parts & Accessories, Router Parts & Accessories, Router Bits, Straight, Spiral & Trim Bits, Straight,

Fully Hardened steel shank. Drill-through pilot for guiding on templet or framing after panel has been mounted. For window and door cutouts in abrasive insulation materials, plywood, and paneling. Single Flute allows for faster feed rates.

Brand	BOSCH
Brand	‎BOSCH
Country of Origin	‎USA
Customer Reviews	4.4 4.4 out of 5 stars 30 ratings 4.4 out of 5 stars
Cutting Angle String	135 Degrees
Cutting Angle String	‎135 Degrees
Domestic Shipping	Item can be shipped within U.S.
Finish	‎Titanium
Finish Type	Titanium
Finish Type	‎Titanium
Included Components	‎
International Shipping	This item can be shipped to select countries outside of the U.S. Learn More
Is Discontinued By Manufacturer	‎No
Item model number	‎85146
Item Package Quantity	‎1
Item Weight	‎0.16 ounces
Manufacturer	‎Bosch
Material	High Speed Steel
Material	‎High Speed Steel
Package Dimensions	‎5.12 x 3.35 x 0.12 inches
Part Number	‎85146
Shank Type	Straight
Shank Type	‎Straight
Surface Recommendation	‎Alloy Steel

5 Star

4 Star

3 Star

2 Star

1 Star

Write your review

Your email will not be published. All mandatory fields are marked with^*

Your rating

Scritto da: Ace of Spades Customs

Great

I use this for trimming aluminum skin and it works great. Aluminum does not stick to it like a carbide cutter.

Scritto da: Wade

just ok

I have used this bit over the last three days to cut window and door openings in faux brick 1/4 inch paneling. I am not sure of the material, but assume it is mdf of some nature. I have cut roughly 60-70 linear feet of material with this bit so far. It cuts fairly well, but seems to bog down occasionally. For actual cutting, I'd give it a 7 out of 10. I do not find the drill through point to work well at all. It is hard to keep in place until it punches through, at least on the material I am cutting. The reason I have given it four stars is because the bit gets so hot it is literally causing fires in the dust it creates. I have tried every speed from slow to max but the bit is scorched black. Not being sure if this was user error or the product being cut, I tried a normal flush cut bit and did not experience the heat/scorching at any speed. This is such an issue, I now have a fire extinguisher next to me for the remainder of the project. update: After making several more cuts, this bit is creating too much of a fire hazard to continue using it. At one point today, I literally had over ten smoldering areas in the dust after a single cut. With the amount of fine debris present, this could lead to a serious issue. The "guide" portion of the tip also does a very poor job on inside corners, it will easily allow the bit to continue straight and cut right into whatever edge you are following, for me it's a window frame. I went to a big box hardware store and paid $23 for a name brand flush cut bit that has 3 cutting blades and a true ball bearing type guide wheel. This new bit is 100 times better than the Bosch bit.

Scritto da: Amazon Customer

Very Good low Budget Router bit

Very Good Low Budget router bit I use them for trimming thin .024 aluminum sheets

Scritto da: Amands see

Works perfect

Works awesome

Scritto da: Teresa

Cuts well.

I had to replace 2 windows and had put the new Zip system panels up. I used this bit to trace the inside of the opening and cut the 7/16 OSB for the new windows. It worked like a charm.