BOSCH RA1151 Router Subbase Centering Pin and Cone Router Subbase Only

Name: BOSCH RA1151 Router Subbase Centering Pin and Cone Router Subbase Only
Brand: BOSCH
SKU: 000346397390
Price: 30.02 EUR
Availability: InStock

Brand:BOSCH

3.7/5

€
30.02

The BOSCH line of countersinks are great for deburring and chamfering openings to pre-drilled holes. Great for electrical, plumbing and HVAC contractors. BOSCH countersinks cut varied materials cleanly and accurately. With standard high-speed steel and super hard titanium-coated bits, these countersinks perform great in even the toughest materials.

Amount

Add to Cart Buy now

EAN: 000346397390

Categories Tools & Home Improvement, Power & Hand Tools, Power Tool Parts & Accessories, Router Parts & Accessories, Tables,

Used for centering template guides. For Bosch routers that have the Precision Centering Design. For precise centering of template guides and attached subbases.

Batteries Included?	‎No
Batteries Required?	‎No
Brand	BOSCH
Brand	‎BOSCH
Customer Reviews	4.7 4.7 out of 5 stars 2,293 ratings 4.7 out of 5 stars
Finish	‎Titanium
Finish Type	Titanium
Finish Type	‎Titanium
Is Discontinued By Manufacturer	‎No
Item Dimensions LxWxH	1.01 x 3.92 x 6.39 inches
Item Dimensions LxWxH	‎1.01 x 3.92 x 6.39 inches
Item model number	‎RA1151
Item Package Quantity	‎1
Item Weight	‎0.32 ounces
Manufacturer	‎Bosch
Material	High Speed Steel
Material	‎High Speed Steel
Part Number	‎RA1151
Product Dimensions	‎1.01 x 3.92 x 6.39 inches
Shank Type	Straight
Shank Type	‎Straight
Style	‎Router Subbase Only
Tool Flute Type	‎Straight

5 Star

4 Star

3 Star

2 Star

1 Star

Write your review

Your email will not be published. All mandatory fields are marked with^*

Your rating

Scritto da: Jake Young

Alignment tool for guide.

Perfectly aligns the template guides to the router collet. It is a must have to use the Porter Cable guide adapter for your Bosch router.

Scritto da: Kyle Fogel

A must for guide bushings

I bought this to help dial in my plunge router for use with a guide bushing. When your using a 1/4 up it bit with a 5/16 bushing there’s not much room for error. This item works perfectly for centering your router plate to the spindle. A mush for anyone using guide bushings with tight tolerances.

Scritto da: Larrie W. Petty

As advertised

As advertised

Scritto da: Joshua Freier

Exactly what you need

If you're looking at this piece, chances are you need this for your router. Skip the foreplay and just buy it. I did a lot of looking around and came back to this. Take my word and save yourself some time.

Scritto da: A Prime Customer

Does what it’s designed to do

Makes aligning the inlay base on my Bosch plunge router easy and accurate.

Scritto da: DMK

It worked.

I needed a base plate for a Craftsman router I had removed from a router table to reuse for dovetailing with a special nonstandard guide. (Craftsman tool parts are largely not available any more). I fabricated a new base plate from some acrylic sheet and used this tool to center the plate to the router with the guide installed. It worked fine.

Scritto da: BluNunn

It works

This should have come with my router kit but it works fine to aline the bases.

Scritto da: RAMON G.

GOOD PRODUCT

GOOD PRODUCT

Scritto da: Harry K.

There are times when the correct tool makes a hobby more enjoyable

My purchase arrived on time and it was well packaged. On opening the contents were in sound condition and using it has been a pleasure. A good experience.

Scritto da: Johnjake

What can you say

You could not make it any easier

Scritto da: João F.

Router subbase

Never used . But looking forward to use .

Scritto da: T. Bessent

A must when using non-factory base plates

Simple to use and works evertime

Scritto da: Yakherder

Poor Quality Control

Needed this product to center the base plate on my routers to center my template bushings. Delivery was fast. Outside package was left on my doorstep, which was as expected. The packaging for the centering pin showed scuffed and torn but I don't believe this caused any cosmetic damage to the part itself. Upon examining the parts I noticed that the pin did not extend through the inside of the cone. As seen in the pictures 1 and 2, it appears that the top of the cone had been snapped off as it came through the manufacturing process and was never cleaned up. I was going to return for another but I had the equipment in my shop to make it work. I placed the 1/4" pin in my drill press and trued the 1/2" end of the cone until the pin would easily move through with slight hand pressure. I had to remove approximately 3/16" of material. I have not used this product for it's intended purpose yet but I expect it will work as intended.