CURT 19101 Camper Hitch for 2 x 4-Inch RV Bumper, 2 in. Receiver, 3,500 lbs

Brand:CURT

3.4/5

€
168.48

A CURT RV hitch is a trailer hitch that is designed to mount onto the back of a recreational vehicle to add extra cargo space. These hitches are manufactured using CURT's quality processes of robotic welding, thorough cleaning and precise finishing. Our RV bumper hitches are coated with a liquid A-coat followed by a gloss black powder coat finish for lasing resistance against wear and corrosion, and they offer a 2" x 2" receiver tube opening. This particular bumper hitch features a gross trailer weight capacity of 3,500 lbs. and a tongue weight capacity of 350 lbs., making it an excellent choice for towing a bike rack, cargo carrier, boat trailer or small utility trailer behind your RV. It can also be used for towing a recreational vehicle trailer, allowing you to bring with you that ATV, personal watercraft, dirt bike or whatever toys you like to have along for the ride. Be sure to always check the gross trailer weight and weight rating of the bumper before towing. CURT RV hitches are not just another accessory for your camper; they are a product of smart engineering and quality construction to help you achieve that ultimate RV experience every time you hit the road.

Amount

Add to Cart Buy now

EAN: 0612314009947

Categories Automotive, Exterior Accessories, Towing Products & Winches, Hitches, Receivers,

EASY TO INSTALL. Installation of this RV camper trailer hitch is fast and easy. It securely bolts onto virtually any 2-inch x 4-inch RV bumper with the included grade-8 hardware and typically just a few tools. RUST, CHIP, UV-RESISTANT. This camper bumper hitch is protected with a dual-coat finish of rust-resistant A-coat and highly durable black powder coat. The finishes are co-cured for exceptional resistance to rust, chipping and UV rays. FULLY TESTED. Every CURT camper hitch design is tested at our Detroit engineering facility according to SAE J684 standards for the utmost safety and reliability while towing. VERSATILE DESIGN. This trailer hitch RV equips your camper with a standard 2-inch x 2-inch hitch receiver, allowing for a wide variety of towing options. It can accept a ball mount, cargo carrier, bike rack, tow hook and much more. DEPENDABLE STRENGTH. This RV trailer hitch is rated for 3,500 lbs. gross trailer weight and 350 lbs. tongue weight (limited to lowest-rated towing component).

Brand	CURT
Brand	‎CURT
Country of Origin	‎USA
Customer Reviews	4.3 4.3 out of 5 stars 231 ratings 4.3 out of 5 stars
Exterior	‎GLOSS BLACK POWDER COAT
Finish Type	GLOSS BLACK POWDER COAT
Is Discontinued By Manufacturer	‎No
Item model number	‎19101
Item Weight	‎12.62 pounds
Manufacturer	‎Curt Manufacturing
Manufacturer Part Number	‎19101
Material	Carbon Steel
Model	‎RV Bumper Hitch
OEM Part Number	‎19101
Product Dimensions	‎11 x 9 x 6 inches
Vehicle Service Type	Marine-Personal-Craft, Off-Road-Motorcycles, ATV, Trailer

5 Star

4 Star

3 Star

2 Star

1 Star

Write your review

Your email will not be published. All mandatory fields are marked with^*

Your rating

Scritto da: Matt Rosario

Didn't fit my bumper, believe the part was defective

Did not fit my bumper. I believe it was defective (poor quality control). There were weld beads that ran to the inside of the mount that sat against the bumper that prevented the bolts to align with the holes. The product seemed sturdy and able to hold a good amount of weight, if only I could have used it. I sent the item back for a refund with zero issues.

Scritto da: Doug

Very Nice for Camper hitch

We bought this and attached it to the Y frame on the front of the camper. We use it to store our weight distribution hitch so that is does sit in the truck. We lock it in and it is out of the way.

Scritto da: Amazon Customer

Cut to Fit

This is an update to my original review. I originally returned the Curt camper hitch in the hope of finding something that fits better. Failed in that goal and rebought the item. Had to seriously modify the hitch to fit it on my aluminum camper trailer. (I only need it to store my truck's bed extender.) Using a angle grinder to cut the hitch down to fit was actually the easy part. Drilling new holes in the very thick steel was non-trivial. Think it will be fine.

Scritto da: Richard Lindley

Saved me big bucks!!!

If you are mechanically inclined this will work on a Highlander bumper. Drilled the aluminum bumper slipped this right in place trimmed the bumper cover been hauling trailers ever since. You don't need a converter switch installed under your dash either or a fuse in your fuse box. Your lights will go onto a line that will always have power as long as the switch is on. Find your signals and your break. That's it you will always have daytime running lights but saves you the time and money for the converter that will pulse your lights. This is because most vehicles don't have a separate signal light like the highlander. Most vehicles pulse the taillight for the signal already.

Scritto da: aric kane varner

Great Receiver for Trailer!

I took and cut this down and re-drilled the top holes to fit the 2"x3" rear cross rail at the back of my boat trailer. Added a pigtail to the back of the boat trailer to plug the ski trailer into for the lights. Now I can pull my jet ski behind my boat like a champ! I ran that boat/ski trailer combo all summer long at 80 mph! No problems whatsoever! Heavy duty construction! Nice black finish! Well built product! Very pleased!

Scritto da: josh warren

Fits a Boss plow crossmember on a 2015-2019 GM HD pickup!

After I had my plow installed I wasn't thrilled about losing my front receiver. I measured the plow crossmember and guessed that this would fit, and I guessed right.

Scritto da: RickieDean

Just what i needed

I installed this hitch on the back of my Toy Hauler Travel Trailer to carry our Bicycles,the Curtis hitch is very well maid, easy to install and allows me to use my hitch bike rack,Love it.

Scritto da: Poolplayer

Description is Misleading - 4"x2" bumper

I wanted to leave this information so others won't be as confused about this product as I was. I was very hesitant to order this as I was looking for a camper bumper hitch to be used for a bike rack. My camper bumper is 4" high by 2" deep. Most rv bumper hitches are for a 4"x4" bumper and this one (Curt 19101) on Amazon and most other web sites that sell this, specify it will fit a 2" square channel bumper. This description in wrong as it fits and is made for my 4"x2" bumper!!!!! Chalet Arrowhead Very solid product and as always, Amazon Prime shipping was fast, showed up next day!

Scritto da: ken

Quality

Great quality and easy to install.

Scritto da: Ryan K.

Great hitch

Bought for a bike rack on my 2x4 C channel bumper on my camper trailer. Very heavy duty hitch... Way more than I needed. Had to do some minor modification to my bumper for it to bolt on properly. For the price, it wasn't worth sending back and only cost a few bucks to do the modifications to make it fit. Great product.

Scritto da: Mike M

Great addition to our trailer for carrying accessories

Works great to add a bike rack to our pop up trailer

Scritto da: Dave Pringle

Worked for me, a cheap alternative

I bought this hitch for a 2014 Mitsubishi Mirage, not to use to pull anything but as a means of being able to mount a 'load extender' type of thing onto the hitch and thereby help carry kayaks and canoes. I'm sure it will also come in handy on trips to the lumber store etc. The problem everyone who will have done this knows, is that mounting a kayak or canoe to a roof rack requires a person to twist their back around in a way that can cause a problem, especially when you get to my age. With an extender, one can tip up the front of the canoe/kayak onto the bar and then slide it forward onto the vehicle. I have not as yet tried this but am looking forward to using this new system!

Scritto da: maryse

Very solid !

I found this piece to be excellent and well made. It didn't suit us for what we needed it for but I definately recommend it if you have the right size bumper.