Jonard Tools TM-25 Mammoth™ Insta-Lock™ Tape Measure, 25' Tape Measure, Auto Lock

Brand:JONARD TOOLS

3.6/5

€
40.92

Designed with high impact housing and a convenient auto-locking mechanism, this tape measure is perfect for any jobsite. The high impact housing protects it from falls and other damage, while the auto-locking mechanism automatically holds the blade in place for maximum accuracy and precision. This tape measure also features the following: Ruler marked with English and Metric units Auto-lock mechanism automatically holds blade in place for accuracy and control 25 ft of reach to get measurements from far distances High impact housing with non-slip TPR grip protects it from damage and stands up to any jobsite demands Tape coating prevents abrasion with repeated use Easy-to-read measurements marked with lines every 1/32" for the first foot, then every 1/16" after 1" wide blade makes this great for hard-to-reach places Convenient belt clip for on-the-go use

Amount

Add to Cart Buy now

EAN: 0810053350867

Categories Tools & Home Improvement, Industrial & Scientific, Measuring & Layout Tools, Linear Measurement, Tape Measures,

RUGGED BELT CLIP: Convenient belt clip for on-the-go use. EASY-TO-READ MARKINGS: Tape is marked with metric and English units, and has a matte finish to mark with a pencil as needed. 25 FT REACH: 25 ft of reach with 1" wide tape to get measurements from far distances easily. HIGH IMPACT HOUSING: With non-slip TPR grip protects it from damage and stands up to any jobsite demands. INSTA-LOCK MECHANISM: Automatically holds tape in place for superior accuracy and control.

Blade Length	25 Feet
Brand	JONARD TOOLS
Color	Blue
Country of Origin	China
Item model number	TM-25
Lock Type	Automatic
Manufacturer	Jonard Tools
Package Dimensions	6.5 x 4.41 x 1.97 inches; 14.99 Ounces

5 Star

4 Star

3 Star

2 Star

1 Star

Write your review

Your email will not be published. All mandatory fields are marked with^*

Your rating

Scritto da: JD Snacker

Awesome product

I purchased this to cut various sized holes in my ceilings for recessed lights and whole-house audio speakers; 50+ holes of various sizes. This is a substantial, heavy duty, super sturdy/rugged tool…. It is not flimsy or “cheap” in construction. Works like a champ and the dust shield really helps contain the drywall dust. The only recommendation I would make for anybody considering this tool is to buy the version with the vacuum port to further mitigate the dust by eliminating the need of dumping it. I did not know a version with a dust port was available when I purchased this.

Scritto da: BigE

Check your cutter installation first before you start.

I think I know why some of you had a miserable time using this tool. Mine came with one of the cutters facing the wrong way! The instructions don't make this clear, but as an experienced machinist I understand carbide cutting tools. The flat carbide surface must face the direction of the cut. If you lay the cutter arbor assembly in front of you on a surface, with the the drill tip pointing away from you, one of the carbide tools will be on the left, the other on the right. For clockwise drill rotation, the cutter on the left should have the flat carbide surface facing up. The left one should be facing down. That way as the assembly rotates, both cutters are engaging the material in face-first orientation. (See my first photo and visualize it rotating clockwise with the drill.) Mine came with both cutters facing up. One cutter would have just dragged through. I guess the Chinese assemblers weren't trained. Also, for optimal cutting, the sharp corner of the cutting tool should be outermost, as in my second photo. But two of mine came with the opposite orientation, as shown in my third photo. Perhaps their intent was to use one of each. That way you would be cutting the inside and outside kerf in unison. Worth a try. The most important thing is to point them in the correct direction, as in my first photo. Otherwise this is an elegant solution to minimizing dusty hole cutting in sheet rock. Nice case. Fits my shop vacuum perfectly. CHECK YOUR DIAMETER SETTING AND TIGHTEN EVERYTHING WELL. Practice on some scrap material if you can, and check the screw tightness every hole.

Scritto da: Francesco

It works, but the instructions could be more clear.

This is a well-made accessory. Yes, you’ll need a drill with adequate torque, but what handyperson or tradie who’d spend $80+ on this hole saw doesn’t own a modern cordless drill with gobs of torque? My non-Fuel 18V Milwaukee had zero trouble with it. A side handle would definitely help stabilizing it, but I still had no issues. My only beef is that what seemed like the logical way to set the size — on the flat (outside) of the blade — is in fact wrong; you have to slide the blade holder *past* the measurement and line up the curve of the holder with the marking on the beam. Easy enough to see the wrong size on a smaller hole, but setting for an 8¼” diameter for my first try it wasn’t noticeable until I finished the cut. Now waiting for the mud to dry after putting the plug back in the wall (because it’s the only way I’ll be able to re-cut it)! I saw the error and adjusted the tool and cut three other holes in around five minutes. I have another couple of dozen holes to cut here and at another property. Oh. And really pay attention to the location of studs, blocks or furring strips/joists in the cavities you’re trying to hole. The blade will bind and the drill will buck in the blink of an eye! That first hole taught me *two* lessons, there was a block where none were expected. Overall an incredibly useful addition to my tool box.

Scritto da: Troy Lemons

Awesome hole cutting tool

This is one of the best tools I’ve purchased It does exactly what it’s made for Cuts perfect holes and you have no dust flying around It’s easy to clean up and the carrying case is very nice and sturdy

Scritto da: Q

Great buy

Got it for Christmas Gift last year and my brother still uses it.

Scritto da: KD9BWI

Not great for OSB

Worked great for cutting in supply diffusers on drywall. I decided on a new construction job to try it's claimed ability to cut plywood/osb. The trick with drywall was to go slow with a fast drill speed to keep the teeth from jamming. I did the same thing on OSB, it tried to cut but ended up snagging and breaking the pilot bit before the drill's anti-kickback could do it's thing. The saw is also VERY particular about keeping COMPLETELY or else it's try to "skip".

Scritto da: Dr. Q

No mess!

There was no mess/dust after drilling a hole in the ceiling.

Scritto da: Ray

drilling works great, but the bowl cannot collect the dusts well when I drilling ceiling holes.

drilling works great, but the bowl cannot collect the dusts well when I drilling ceiling holes. for wall drilling, it simply fine

Scritto da: Taylor

Bit broke right away and cant replace

seemed like good quality when it arrived, but the center bit broke on the second hole i drilled. it doesn't appear that you can replace the bit either, so it is now useless to me