PEI Sheet 235mmx235mm and Magnetic Sticker with Adhesive for Creality Ender 3/Ender 3 Pro/Ender 3 V2/Ender 3 S1/Ender 3 S1 pro/Ender 3 neo/Ender 3 v2 neo/Ender 5/Ender 5 Pro/Voxelab Aquila 3D Printer

Name: PEI Sheet 235mmx235mm and Magnetic Sticker with Adhesive for Creality Ender 3/Ender 3 Pro/Ender 3 V2/Ender 3 S1/Ender 3 S1 pro/Ender 3 neo/Ender 3 v2 neo/Ender 5/Ender 5 Pro/Voxelab Aquila 3D Printer
Brand: UNIDO
SKU: 0783970029096
Price: 45.94 EUR
Availability: InStock

Brand:UNIDO

3.6/5

€
45.94

【Wide Application】The size of Ender 3 PEI is 235*235mm（9.25*9.25inch). After installing the print bed, please re-level it to improve the printing effect. , it is applicable with Creality 3D printers such as Ender-3, Ender-3 Pro, Ender-3 V2, Ender-3 S1,Ender 3 S1 pro,Ender 3 neo,Ender 3 v2 neo, Ender-5, Ender-5 Pro, CR-20, CR-20 Pro, Voxelab Aquila, Voxelab Aquila C1, Voxelab Aquila C2 and and similarly sized FDM 3d printers.Compatible with PLA/PETG/PEEK/ABS and any other filaments. 【More Affordable and Practical】 We use 75% thicker PEI and 25% thicker spring steel than our leading competitors. This means a more durable plate that can handle the tough conditions of 24/7 printing. Our magnet can also sustain higher temperatures of 120°C，Wear-Resistant and Scratch-Resistant, easy to clean: There is a protective film on the surface of the composite coating, which is of anti-scratch and dustproof, etc. 【Simple Installation】The Ender 3 V2 PEI sheet is combined with 2 parts, a flexible steel platform textured PEI surface on one side, Simply stick the magnetic bottom sheet onto your heated bed, then place the steel platform with PEI surface on the top.Spring stainless steel, PEI powder sprayed on the surface, golden yellow on the back. Flexible, removable, and can stick to magnetics very well. High strength and heat resistance. 【Easy Removal】When used in a 3D printing application, PEI is excellent because it can withstand the numerous heat cycles that a 3D print bed goes through from print to print.This surface is easily removed and flexible. Prints come off the surface easily when the temperature of the heated bed reaches room temperature. If the print is still stuck, remove the upper magnetic surface from the lower, bend the flexible surface and watch the model fall right into your hands. 【Excellent Adhesion】Easy to adhere to the printing surface, easy to remove the prints, flex slightly to pop your print right off. Excellent adhesion can be achieved when the temperature of the heated bed is about 60℃, PEI sheet without using any glue or other tools to help the model to stick onto the sheet.

Amount

Add to Cart Buy now

EAN: 0783970029096

Categories Industrial & Scientific, Additive Manufacturing Products, 3D Printing Supplies, 3D Printing Filament,

Country of Origin	China
Item model number	PEI-1230
Manufacturer	Unido
Package Dimensions	10.87 x 10.59 x 0.83 inches; 1.12 Pounds

5 Star

4 Star

3 Star

2 Star

1 Star

Write your review

Your email will not be published. All mandatory fields are marked with^*

Your rating

Scritto da: Cutter

Your mileage may vary

I ordered this magnetic sheet set primarily based on the claim of it being able to withstand over 100C bed temperatures, as I planned to use it on a printer used mainly for ABS and PETG. It's on an Ender Neo converted to an Ender 3 Pro by replacing the mainboard and removing the CR-touch... I get better results manually leveling and enjoy being able to use the ENTIRE 235mm bed surface (set your bed offsets if you're missing a few mm on the left and front). The magnetism is scary strong - like it'll bite you if your finger gets in the way, and once it's down it is REALLY down. (raise the extruder up out of the way and carefully align the back edge of the PEI sheet with the bed with the front raised about 30 degrees. Once the back edge and corners are aligned, slowly lower the front until it snaps into position). I have had it to 110 degrees with absolutely no apparent reduction in magnetism. The textured surface seems rock solid - more like anodized aluminum than PEI (the Gizmodorks PEI sheet on another printer feels much softer). As to the build surface, the textured side works great, albeit leaving a bottom texture reminiscent of my blue-tape-using days, but I can't get a single thing to adhere to the smooth side. The ONE time I actually got a PLA print with a 5mm brim to stick, it actually curled up at about 6mm thickness... which I have NEVER seen PLA do. I ran the bed at 65 C to get the brim to stick, and apparently the combination of insufficient adhesion and PLA softened by the bed heat (full fan, but this sheet seems to transfer heat to the model much more readily than other surfaces I've used) made it decide to curl. The textured side works great at 60 degrees for PLA, but I got ZERO adhesion on the smooth side at that temperature. Reflecting back on my learning process over the past seven years, relatively thick (over .5mm) Kapton tape was the game changer on my Prusa clones, and I got into the habit of printing PLA on a 60C heated bed (ABS at 90-95 in a 45 degree enclosure). I like the Kapton much more than PEI, but can't find any that's more than a few mils thick. The "official Creality" build surface did nothing for me, and glass - even using the specially surfaced plate that came with the Neo, has always been an exercise in futility for me. In summation, I'm debating ordering another of these, but leaning toward a similar set with both sides of the top sheet textured, or with a double-sided textured sheet and double-sided sheet with carbon fiber stripes. If I order this again at least maybe I'll know if I got one with a bad smooth-side coating.

Scritto da: teamhex

Impressive. Big upgrade over the stock PC sheets.

I come from the days of using painters tape and Kaplan tape for adhesion on glass. Glue sticks and hairspray as well. I recently got back into printing after picking up an Ender 3 S1 and a 3 Pro. Love them and my mind was blown by the flexible PC sheets that came with them. I used the stock sheets for 2-3 months and finally I’m running into issues with them. I bought this and threw it on my S1. I can’t believe how much better this is. I mean prints pop themselves off the bed when they cool. Yet when it’s hot during printing it sticks to the sheet very well. It’s a game changer and I’m considering getting a second. I have been switching between glass and PC sheets, but if this thing holds up, I’ll probably use it going forward. I feel like my first layers are better as well. Could be my imagination, but this is quite amazing. I recommend you pick one up.

Scritto da: FAT-DAD

Sticks great

The first few prints had a problem with sticking. A corner here and a corner there wouldn’t stick. Now everything sticks, but everything comes off easily when done. I haven’t had to clean it at all. This thing is great.

Scritto da: VegasHotWheeler

Nice!

Have only done a couple of print, but I like it so far.

Scritto da: Ronnie V.

Essential 3d Printer Upgrade

If you have yet to try a PEI sheet for your 3d Printer yet, you are missing out on the ease of use and end of much frustration. This PEI has a smooth side and a textured side if you want the smoothness that you can get out of your glass sheet. I highly recommend this as an essential printer upgrade, you will not regret it, and no more scraping and fudging to get your prints off the bed. This installs in seconds, and only requires a quick relevel. One bonus of this sheet is the dual tabs making it easy to lift off from either side of the bed. Again highly recommend this for your Ender3v2 not sure why I waiting so long.

Scritto da: spadic

Works great!

Had to cut slots for my exposed screws on my 5 S1 bed but it is the correct size. Couldn’t find just the metal plate! My 5 S1 already has a magnetic base.

Scritto da: Shane

Product works great, prints stick during the print and come off easily when cooled

The will fit multiple printers as long as the bed size is 235x235. I tested on a Fookos Odin F5 and it fit perfect. Reversable, with both textured and smooth. I was a bit worried about the smooth side as it doesn't appear to have a PEI sheet, unless it's incredibly thin. However after printing on it, it works great I was surprised how well the print stuck to the smooth side of the bed, with the bed still warm I had to use a bit of force to remove the print, which says to me it wasn't going anywhere. Personal preference for most on the smooth vs textured. Personally either one works for me, both side worked well, and function as expected. I did include a picture to show the texture vs smooth bottom finish The included magnet sheet is very strong, grabs the print surface very firmly.

Scritto da: Killerdave

Works great and at good price.

I love this sheet it sticks very well. It's better then the glass I had.